Pipes polypropylene jakko. Which polypropylene pipes to choose: saving without loss of quality

In production JAKKO polypropylene pipes only the best equipment and raw materials are used. Continuous market research polymer materials allows the manufacturing company to introduce into production Newest technologies, which makes it possible to increase production capacity and range of products.

Jakko polypropylene pipes are widely used for heating and water supply systems in residential buildings and public institutions.

Due to its unique characteristics polypropylene pipes JAKKO for heating, hot and cold water supply are considered the most promising, and the demand for them is steadily growing. Now in most countries, including Russia, there is an active rejection of traditional steel pipes in favor of polypropylene pipelines.

• Plumbing systems:

Polypropylene pipes are excellent for laying cold and hot water supply networks with operating temperature up to +95 degrees. Service life of pipes, at the correct installation, not less than 50 years. Pipes PN 20 are suitable for cold and hot water.

• Heating systems:

For hot water and central heating, organized, for example, using aluminum radiators, PN 20 pipes are suitable, but PN 25 pipes are used more often - polypropylene pipes reinforced with fiberglass.

Plastic pipes for heating and water supply are much more convenient and easier to install than metal ones. When installing pipes, both for heating and for water supply, it is necessary to comply with the relevant standards and carry out the necessary calculations.

Which polypropylene pipes to choose - this question is asked by every user who decides to opt for polypropylene products, starting a construction site or repairing an existing plumbing system. Our article will help you not to get confused in the variety of manufacturers of polypropylene pipes. We also offer brief description products in the budget price category for those who want to save money without sacrificing quality.

Which pipes to choose?

1. Products made in Germany:

• Banninger;
• Akwatherm;
• Wefatherm;
• Rehau. Characteristics of each of them in the article "".

1. Czech pipes are confidently in second place:

• ECOPLASTIC;
• FV-Plast (you can find them in the article "").

1. In third place are cheaper and slightly inferior in quality products from Turkey (in the section “Turkish polyethylene pipes" below):

• TEBO;
• Pilsa;
• Vesbo;
• Valtek;
• FIRAT;
• Kalde;
• Jakko;
• Dyzain (their characteristics are below "").

1. China is not happy with the quality, the exception is the brand

• BLUE OCEAN (reviews of Chinese products below "").

1. Finally, the budget option is Russian-made products:

• PRO AQUA;
• Heisskraft;
• Santrade;
• Politek (reviews on more popular manufacturers in the article "").

So, let's proceed to the consideration of products from Turkish and Chinese polypropylene.

Turkish pipes

TEBO pipes

Pipes, which are produced by the TEBO technics trademark, have a diameter of 20-160 mm. These pipes are presented on the market in a wide range, which allows for the installation of heat supply and water supply systems for industrial purposes. Turkish polypropylene pipes are quite good at transporting a range of aggressive chemicals.

TEBO pipes have been used, and quite successfully, for several years for water and heat supply. A wide range of TEBO technics products includes a line of polypropylene pipes PN10, PN20 designed for water supply systems. The company for the installation of heating systems in buildings produces pipes that are reinforced with aluminum or fiberglass. The suitability of pipes, according to reviews, is regarded as "middle class". Many masters did not have any problems during long-term work with TEBO.

Pilsa pipes

Pilsa polypropylene pipes, made in Turkey, differ from other pipes in wear resistance, strength, and elasticity. This is what helps to successfully use them in systems:

• heat supply;
• hot water supply;
• cold water.

When installing reinforced pipes PN20 for heat supply, PN20 for hot water supply, and PN10 for cold water supply, all products will serve for a long time, and for several years you will not be bothered by any problems associated with their operation. It is only necessary to follow all the recommendations of the manufacturer when installing them. So, for example, Pils pipes do not need to be walled up, and the boiler must be installed in a controlled manner so that pressure does not exceed 95 degrees into the system.

Some reviews also note disadvantages: most often, Pilsa and Firat pipes have an oval pipe, and on the one hand, when stripping, aluminum often remains that needs to be cleaned.

Turkish pipes Valtek and Vesbo

Wesbo pipes manufactured by Novaplast - Turkey have high quality, but at the same time their price is relatively low. But the choice of shaped elements is quite modest, although this can be considered the only negative. Wesbo pipes are widely used.

VALTEC company, which produces polypropylene fittings from polypropylene, the brand of which is PP-R 100, which makes products more reliable and durable. Turkish pipes VALTEK have a round shape, and the foil is perfectly even, as the installers using the products say.

Firat pipes

Turkish pipes and fittings of the Firat PPRC system are produced in accordance with the standards. The company has been in the lead for many years. According to customer reviews, Firat plastic pipes have proven to be excellent, for several years of their operation there have been no technical problems. Turkish pipes are unpretentious and easy to use - they do not rust, so there is no need to paint them. The only disadvantage of these pipes is considered to be a large coefficient of expansion when heated, as a result of which, when installed on hot water, the pipes can lead.

Kalde - Turkish pipes

Kalde pipes made in Turkey are often compared with Ecoplastic, although they differ from it, since these pipes have a solid aluminum shell, while Ecoplastic has a perforated, that is, with holes, the inner layer of plastic is gray, Ecoplastic has a similar to polyethylene, with white shade, translucent.

Calde pipes made of polypropylene, according to customer reviews, are worse than Vavin pipes, since their material is more pliable and soft, there is no perforation on the aluminum layer, as a result of which it can peel off the plastic. Also, compared to the perforated layer, the solid layer loses.

Pro tip:

When improperly installed, such pipes become covered with bubbles. This type pipes cannot be walled up in walls, they should only be placed on top.

Jakko pipes

Jakko produces a fairly wide range of products. Consumer reviews about them differ slightly.

Installers praise fiberglass reinforced pipes, which proved to be good when soldering.

However, some of them note swelling when using Jacco in tying boiler rooms. In particular, leaky joints usually appear with installers with little experience. At the same time, when using products in cold water pipes, such problems were not observed at all.

When installing long (approximately 9-meter) sections of Jaco pipes, products tend to sag, despite the fact that the manufacturer technical specifications declares minimum linear expansion rates.

Pro tip:

The last drawback can be solved by installing expansion joints in long sections, approximately every 4 meters.

Pipes DESIGN

Dizayn reinforced pipes made in Turkey are supplied in a wide range. These pipes do not require stripping, which makes it possible to sufficiently simplify the installation and dismantling of cold water and hot water systems. Thanks to the special pipe production technology Design, the material and time costs required for preparing equipment for soldering, linear thermal expansion are reduced. In addition, this technology has a more aesthetic appearance of the result.

Almost anyone who does not have any skills can install a pipe made of polypropylene, only after trying a few times. Polypropylene pipes DIZAYN (DESIGN) occupy a worthy place in the Russian market, which is due to the quality indicators of pipes that are not inferior to the products of leading European manufacturers, as well as low prices.

According to pipe buyer feedback good quality, but it is imperative to follow the installation technology, as well as protect them from the outside.

Polyethylene pipes, made in China

blue ocean

Qingdao Blue Ocean New High Technology Co., Ltd, a subsidiary of the UK Blue Ocean International Industrial Group, manufactures good quality polypropylene fittings and pipes.

According to buyers, these pipes are soldered perfectly. Somewhat different soldering iron tips are the rounding located on the inner nozzle, which allows you to better fuse the PP layers on top of the aluminum layer. The only drawback of Blue Ocean pipes is the error of the pipes themselves in the outer diameter, which is somewhat dancing. With joints, Chinese Blue Ocean pipes are connected without problems. If Ecoplastic is compared with these pipes, then they lose, since they melt somewhat worse. In the reviews, the installers note that they are a bit tight to insert into the soldering iron, and the red line is not drawn exactly, almost in a spiral, so it’s impossible to solder exactly along it - only by eye.

We hope you find our review useful. Peshtan pipes not included in the rating are available at the link "".

Company foundation year: 2002

Company JAKKO (Jakko) - polypropylene pipes and fittings

JAKKO was founded in 2002, initially engaged in the supply and wholesale sales polypropylene pipes, but after 5 years launched own production. The company has passed the mandatory certification, according to international standards quality and leads the European market in sales of polypropylene pipes. In Russia, the JAKKO brand appeared relatively recently, two years ago in Moscow. In St. Petersburg officially represents trademark GK "Santekhkomplekt Neva". Only from us you can buy products at the best prices.

Polypropylene pipes and JAKKO fittings (Jakko), advantages:

• High quality materials;
• The product is certified;
• Durability;
• Environmental friendliness;
• Ease of installation;
• Anti-corrosion;
• Thermal resistance.

Polypropylene pipes and fittings JAKKO (Jakko) in assortment:

JAKKO polypropylene pipes:

• Pipes PN 20 for cold and hot water supply and central heating;
• Pipes РN 25 (reinforced) for hot water supply and central heating.

JAKKO polypropylene fittings:

• Combined fittings are made of high quality polypropylene with pressed metal inserts, with external or internal thread, which allows easy transition from polypropylene to metal and vice versa;
• Polypropylene fittings - for connecting pipelines to each other;
• Ball Valves, valves.

Company JAKKO (JAKKO), production:

The company's office and factories are located in Istanbul. JAKKO's production workshop consists of injection molding machines with a capacity ranging from 120 to 350 tons. Thanks to the high technology of the Universal Freze system, the company guarantees high quality products in a short time. Thanks to automated system, the planning department sends briefings and monitors production directly from the office online. Thus, it responds in a timely manner to emerging failures, which contributes to a significant reduction in the percentage of defects.