Knowledge for the fifth grade A mechanic of the fifth grade should know the inner workings well enough. Required knowledge:

• kinematic diagrams of turbochargers, electric motors, steam engines, internal combustion engines;
• high pressure compressor devices;
• operating rules and characteristics of auxiliary equipment, steam engines, electric motors, turbocompressors;
• technological processes stations;
• Compressor efficiency and applied structures and systems.

Sixth grade The work of a sixth grade machinist requires the greatest concentration, and knowledge must be supported not only by theory, but also by practice.

Job description of the driver of compressor units of the 6th category

Compressor unit operator (4th grade) Description of work. Maintenance of stationary compressors and turbochargers with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 100 to 500 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of over 5 to 100 cubic meters. m / min. each when working on non-hazardous gases driven by different motors. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with pressures up to 1 MPa (up to 10 kgf / sq.

cm), with a supply of over 5 to 100 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of up to 5 cubic meters. m / min. each. Establishment and maintenance of the most advantageous operating mode of the compressors. Monitoring the health of engines, compressors, instruments, auxiliary mechanisms and other equipment.

Production instruction for the operator of compressor units (permanent)

Info

Knowledge of the types and types of control and measuring instruments and devices is required to perform the work efficiently. Knowledge of technological processes used in production is a guarantee successful work... It is also necessary to know the principles of operation of the installation, the device of the compressor, electric motors, as well as the instruments with which measurements are taken.

Attention

Categories According to the reference book, there are 5 categories of compressor operators. For each, its own requirements for professional training are put forward, as well as the responsibilities that the employee must fulfill in this position are described. In the ETKS classifier, machinists of the second, third, fourth, fifth and sixth categories are distinguished.

The highest is the second category, it is subject to the highest requirements in terms of experience and skills. The sixth, respectively, is the lowest.

Compressor installation operator: description of the profession

MPa (over 10 kgf / sq. Cm), with a feed over 250 cubic meters. m / min. each when working on non-hazardous gases driven by different motors. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 250 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of over 100 cubic meters. m / min. each. Maintenance of automated compressor stations with a supply of over 100 cubic meters.

m / min. Monitoring the operation of all compressor station equipment. Regulation of the technological process for the production of station products. Compilation of defective lists for the repair of compressor station equipment.

Repair of compressor station equipment within the qualifications of a 5th grade locksmith.

Compressor operator

The operator of compressor units of the 6th category carries out: 2.1.1. Maintenance of stationary compressors and turbochargers with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 1000 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of over 250 cubic meters. m / min. each when working on non-hazardous gases driven by different motors. 2.1.2. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with pressures up to 1 MPa (up to 10 kgf / sq.

cm), with a supply of over 250 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of over 100 cubic meters. m / min. each. 2.1.3. Maintenance of automated compressor stations with a supply of over 100 cubic meters. m / min. 2.1.4. Monitoring the operation of all compressor station equipment. 2.1.5. Regulation of the technological process for the production of station products. 2.1.6.
The operator of compressor installations of the 2nd category should be able to: 1. maintain stationary compressors and turbocompressors with pressures up to 1 MPa (up to 10 kgf / cm2) with a flow rate of up to 5m3 / min each when operating on non-hazardous gases driven by various engines; 2. to start, regulate and stop the compressors; 3. to observe the operation of compressors and auxiliary equipment; 4. lubricate and cool the rubbing parts of the compressor mechanisms; 5. General qualification requirements given for all categories 6. to prevent and eliminate malfunctions in the operation of the compressors and control the operation of its safety devices; 7. to service the drive motors; 8. fill and pump oil into supply and emergency tanks; 9. participate in the repair of compressor station equipment; 10.

404 error page does not exist

CURRICULUM for advanced training of workers in the profession "Operator of compressor installations" of the 3rd category Duration of training - 2.5 months No. Courses, subjects Total hours 1. THEORETICAL TRAINING 1.1 Basics market economy and entrepreneurship 16 12. General technical course 30 12.1. Reading drawings, diagrams 8 1.2.2.
Materials Science 8 1.2.3. Tolerances and technical measurements 8 12.4. Electrical engineering 6 1.3. Special course 92 1.3.1. Special technology 92 2. PRODUCTION TRAINING 242 Training time reserve 8 Consultations 4 Qualification examination 8 Total 400 QUALIFICATION CHARACTERISTICS Profession - compressor unit operator Qualification - 4th grade The 4th grade compressor operator must know and be able to fulfill all the requirements for the operators 3 discharge.

Working instruction for the compressor unit operator (6th grade)

The employee is familiarized with this instruction when hiring (transferring) to work in the profession for which the instruction has been developed. 5.2. The fact that the employee is familiar with this instruction is confirmed by a signature on the acquaintance sheet, which is an integral part of the instruction kept by the employer. Developed by: Head of structural unit:. (surname, initials) (signature) ""
Agreed by: Head (specialist) of the labor protection service:. (initials, surname) (signature) "" Approved by: Head (legal adviser) of the legal service:. (initials, surname) (signature) ""
APPROVED "Name of the employer's position (signature) (surname, initials) Date of approval Production instruction for the compressor unit operator (permanent) (name of profession, position or type of work) (designation) 2014 Present production instruction for the driver of compressor installations (permanent) is developed in accordance with ETKS 1, Rules for the device and safe operation stationary compressor installations, air pipelines and gas pipelines dated June 5, 2003 N 60. 1. GENERAL REQUIREMENTS 1.1. The operator of compressor installations (permanent) is a worker and reports directly to the foreman of the site. 1.2. The operator of compressor installations (permanent) must fulfill his duties in accordance with the requirements of this Instruction.
1.3.

6 compressor unit operator's documentation

For non-fulfillment or improper fulfillment of their duties provided for by this job description - in accordance with the current labor legislation of the Russian Federation. 4.1.2. For offenses committed during the period of carrying out their activities - in accordance with the current civil, administrative and criminal legislation of the Russian Federation. 4.1.3. For causing material damage - in accordance with current legislation RF. 4.1.4. For violation of the internal labor regulations, rules fire safety and safety measures established by the organization. 4.1.5. ... 5. OPERATING MODE 5.1. The operating mode of the driver of compressor units of the 6th category is determined in accordance with the internal labor regulations established in the organization. This job description was developed in accordance with.

We bring to your attention a typical example of a job description for a driver of technological compressors of the 6th category, sample of 2019. A person with education, special training and work experience can be appointed to this position. Do not forget that each instruction of the 6th grade technological compressor operator is handed out against a receipt.

This section provides typical information about the knowledge that a 6th grade technological compressor operator should have. About duties, rights and responsibilities.

This material is included in the huge library of our site, which is updated daily.

1. General Provisions

1. The operator of technological compressors of the 6th category belongs to the category of workers.

2. The operator of technological compressors of the 6th category is a person who has ________ specialized secondary education (education, special training) and work experience in this position ________ years.

When servicing the electrical equipment of a workshop with electrically driven gas pumping units, it must have a group IV for electrical safety.

3. The driver of technological compressors of the 6th category is hired and dismissed by __________ (by whom, position)

4. The operator of technological compressors of the 6th category should know:

a) special (professional) knowledge of the position:

- gas transportation technology;

- layouts of pipelines of the workshop and inter-workshop communications;

- basic information on systems automated control technological process;

— technical conditions and technology for all types Maintenance and repair of compressors, their drives, valves and equipment;

- technology of gas lift and cycling process;

- qualification requirements for this position of a lower category.

b) general knowledge of an employee of the organization:

- rules for labor protection, industrial sanitation and fire safety;

- rules for using funds individual protection;

- the requirements for the quality of work (services) performed, for the rational organization of work in the workplace;

- assortment and marking of materials used, consumption rates of fuels and lubricants;

- rules for the movement and storage of goods;

- types of marriage and ways to prevent and eliminate it;

5. In his activity, the driver of technological compressors of the 6th category is guided by:

- legislation Russian Federation,

- Charter (statute) of the organization,

- this job description,

- The rules of the internal labor regulations of the organization.

6. The driver of technological compressors of the 6th category reports directly to: ______________ (position)

2. Responsibilities of the operator of technological compressors of the 6th category

Technological compressor operator of the 6th category:

a) Special (professional) job responsibilities:

1. Maintenance of compressor stations, shop level control panels, as well as general shop systems for gas purification and dehydration, oil supply, heat recovery at the compressor station.

2. Production of operational switchings at the technological piping of compressor stations, regulation of the shop operation mode as directed by the dispatching service.

3. Removal of technological equipment for repair, participation in its delivery and acceptance from repair.

4. Prevention, identification and elimination of malfunctions in the operation of technological equipment and its systems.

5. Adjustment of compressors, their drives, apparatuses, auxiliary equipment of workshops, compressor stations.

6. Production of operational switching in electrical installations with voltage over 1000 volts in workshops with electric drive gas pumping units.

7. Supervising the work of operators of lower qualifications.

8. Responsibilities of the officials for this position of the lower grade (s).

b) General job responsibilities of an employee of the organization:

- Compliance with the Internal Labor Regulations and other local regulations of the organization, internal rules and regulations of labor protection, safety, industrial sanitation and fire protection.

- Execution within employment contract orders of employees, by whom it was repaired in accordance with this instruction.

- Carrying out work on acceptance and delivery of a shift, cleaning and washing, disinfection of serviced equipment and communications, cleaning the workplace, devices, tools, as well as keeping them in proper condition.

- Keeping established technical documentation.

3. Rights of the driver of technological compressors of the 6th category

The driver of technological compressors of the 6th category has the right to:

1. Submit proposals for the management's consideration:

- to improve the work related to the provisions of this instruction responsibilities,

- on the encouragement of distinguished workers subordinate to him,

- about attracting to material and disciplinary responsibility workers who have violated production and labor discipline.

2. Request from structural units and employees of the organization information necessary for him to carry out his job duties.

3. To get acquainted with the documents defining his rights and obligations in the position held, the criteria for assessing the quality of the performance of official duties.

4. To get acquainted with the draft decisions of the management concerning its activities.

5. Require the management to provide assistance, including the provision of organizational and technical conditions and the execution of the established documents necessary for the performance of official duties.

6. Other rights established by the current labor legislation.

4. Responsibility of the operator of technological compressors of the 6th category

The driver of the 6th grade technological compressors is responsible in the following cases:

1. For improper performance or non-performance of their official duties provided for by this job description - within the limits established by the labor legislation of the Russian Federation.

2. For offenses committed in the course of their activities - within the limits established by the current administrative, criminal and civil legislation of the Russian Federation.

3. For causing material damage to the organization - within the limits established by the current legislation of the Russian Federation.

Job description 6th grade technological compressor driver - sample of 2019. Job responsibilities the driver of technological compressors of the 6th category, the rights of the driver of technological compressors of the 6th category, the responsibility of the driver of technological compressors of the 6th category.

Issue approved by Resolution State Committee USSR for labor and social issues and the Secretariat of the All-Union Central Council of Trade Unions of January 31, 1985 N 31 / 3-30
(as amended by:
Resolutions of the USSR State Committee for Labor, the Secretariat of the All-Union Central Council of Trade Unions of 10/12/1987 N 618 / 28-99, of 12/18/1989 N 416 / 25-35, of 05/15/1990 N 195 / 7-72, of 06/22/1990 N 248 / 10-28,
Resolutions of the State Committee for Labor of the USSR 18.12.1990 N 451,
Resolutions of the Ministry of Labor of the Russian Federation of 24.12.1992 N 60, of 11.02.1993 N 23, of 19.07.1993 N 140, of 29.06.1995 N 36, of 01.06.1998 N 20, of 17.05.2001 N 40,
Orders of the Ministry of Health and Social Development of the Russian Federation of July 31, 2007 N 497, of October 20, 2008 N 577, of April 17, 2009 N 199)

Compressor operator

§ 189. Operator of compressor installations (2nd category)

Description of works... Maintenance of stationary compressors and turbocompressors with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of up to 5 cu. m / min. each when working on non-hazardous gases driven by different motors. Start, control and stop of compressors. Monitoring the operation of compressors and auxiliary equipment. Lubrication and cooling of rubbing parts of compressor mechanisms. Prevention and elimination of malfunctions in the operation of compressors and control of the operation of its safety devices. Service of drive motors. Filling and pumping oil into service and emergency tanks. Participation in the repair of compressor station equipment.

Must know: the principle of operation of reciprocating compressors, turbochargers, steam engines and electric motors; methods of preventing and eliminating malfunctions in the operation of compressors and motors; purpose and methods of application of instrumentation and control automation; compressor station piping diagrams; working pressure by degrees and the corresponding air temperature; permissible heating temperature of units of serviced units, measures to prevent and eliminate overheating; grades and brands of oils used to lubricate mechanisms.

§ 190. Operator of compressor installations (3rd category)

Description of works... Maintenance of stationary compressors and turbochargers with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 5 to 100 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of up to 5 cubic meters. m / min. each when working on non-hazardous gases driven by different motors. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of up to 5 cubic meters. m / min. each. Start-up and regulation of operating modes of compressors, turbochargers and engines. Maintaining the required operating parameters of the compressors and switching over individual units. Detection and prevention of abnormalities in the operation of the compressor station. Maintenance of reporting and technical documentation on the operation of serviced compressors, machines and mechanisms. Participation in the repair of compressor station units.

Must know: device of reciprocating compressors, turbochargers, internal combustion engines, steam engines and electric motors, their specifications and service rules; pipeline diagram; the device of simple and medium complexity of instrumentation, automatic devices and fittings; reporting and technical documentation of the compressor station; fundamentals of thermodynamics and electrical engineering; properties of gases manifested during the operation of compressors.

§ 191. Operator of compressor installations (4th grade)

Description of works... Maintenance of stationary compressors and turbochargers with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 100 to 500 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of over 5 to 100 cubic meters. m / min. each when working on non-hazardous gases driven by different motors. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 5 to 100 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of up to 5 cubic meters. m / min. each. Establishment and maintenance of the most advantageous operating mode of the compressors. Monitoring the health of engines, compressors, instruments, auxiliary mechanisms and other equipment. Participation in the inspection and repair of compressor plant equipment within the qualifications of a 3-grade locksmith.

Must know: design features, the device of various types of compressors, turbochargers, internal combustion engines, steam engines, steam turbines and electric motors, auxiliary mechanisms, complex instrumentation, apparatus and fittings; layouts of steam pipelines, circulation condensation pipelines, fittings and reservoirs of the compressor station; layouts of automatic devices for regulating the operation and blocking of equipment; main technical characteristics of serviced compressors; norms of consumption of electricity and operating materials for the production of compressed air or gases.

§ 192. Driver of compressor installations (5th grade)

Description of works... Maintenance of stationary compressors and turbochargers with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 500 to 1000 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with supply over 100 to 250 cubic meters. m / min. each when working on non-hazardous gases driven by different motors. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 100 to 250 cubic meters. m / min or pressure over 1 MPa (over 10 kgf / sq. cm), with a feed over 5 to 100 cubic meters. m / min. each. Maintenance of automated compressor stations with a capacity of up to 100 cubic meters. m / min.

Switching over and withdrawal to reserve and for repair of compressor station equipment. Regulation of the technological process of production of the station's products. Drawing up defective lists for the repair of compressor station equipment. Repair of compressor station equipment within the qualifications of a 4th grade locksmith. Field repair of compressors and internal combustion engines.

Must know: kinematic diagrams of serviced compressors, turbocompressors, steam engines, electric motors and internal combustion engines; device of high pressure compressors; operational characteristics of compressor and turbocompressor units, steam and electric engines for them and auxiliary equipment; schemes of technological processes of production of the station's product; the efficiency of the compressors of the systems and structures used.

§ 193. Engineer of compressor installations (6th grade)

Description of works... Maintenance of stationary compressors and turbochargers with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 1000 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of over 250 cubic meters. m / min. each when working on non-hazardous gases driven by different motors. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 250 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with a supply of over 100 cubic meters. m / min. each. Maintenance of automated compressor stations with a supply of over 100 cubic meters. m / min. Monitoring the operation of all compressor station equipment. Regulation of the technological process for the production of station products. Compilation of defective lists for the repair of compressor station equipment. Repair of compressor station equipment within the qualifications of a 5th grade locksmith.

Must know: kinematic diagrams and design of turbochargers different systems and types of power equipment: electric motors, steam engines, internal combustion engines; compressor performance and power plants to them.

Note. An assistant driver of a compressor or turbocompressor station is charged two categories lower than the category of the driver, under whose supervision he works, but not lower than the 2nd category.

Operators of mobile compressor units are charged according to the ETKS section "Construction, installation and repair and construction works".

Section "Professions of workers common to all sectors of the national economy"((ETKS # 1))

§ 192. Driver of compressor installations (5th grade)

5th grade

Description of the work. Maintenance of stationary compressors and turbochargers with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 500 to 1000 cubic meters. m / min. or pressure over 1 MPa (over 10 kgf / sq. cm), with supply over 100 to 250 cubic meters. m / min. each when working on non-hazardous gases driven by different motors. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with pressures up to 1 MPa (up to 10 kgf / sq. Cm), with a supply of over 100 to 250 cubic meters. m / min or pressure over 1 MPa (over 10 kgf / sq. cm), with a feed over 5 to 100 cubic meters. m / min. each. Maintenance of automated compressor stations with a capacity of up to 100 cubic meters. m / min.

Switching over and withdrawal to reserve and for repair of compressor station equipment. Regulation of the technological process of production of the station's products. Drawing up defective lists for the repair of compressor station equipment. Repair of compressor station equipment within the qualifications of a 4th grade locksmith. Field repair of compressors and internal combustion engines.

Should know: kinematic diagrams of serviced compressors, turbocompressors, steam engines, electric motors and internal combustion engines; device of high pressure compressors; operational characteristics of compressor and turbocompressor units, steam and electric engines for them and auxiliary equipment; schemes of technological processes of production of the station's product; the efficiency of the compressors of the systems and structures used.

	(next) ->

The compressor operator is a specialist who ensures uninterrupted operation, maintains it, prepares it for starts and stops. In his work he is obliged to maintain the established technological rhythm.

With the help of automation equipment, measuring and control devices, protection and alarm systems, as well as blocking, the compressor unit operator inspects the equipment and determines the causes of breakdowns, after which they eliminate them.

Requirements

The job description of the compressor unit operator describes a list of duties for which the absence of contraindications is required. If an employee has health problems, then it is strictly forbidden to work on this installation.

The compressor operator must have vision that is resistant to fatigue. Sharp vision with normal color discrimination is one of the important criteria.

Good hearing, fine sense of smell, developed memory- qualities that must be at a high level.

Physically demanding work requires a lot of stamina. In case of health problems, as a result of which heavy physical activity and monotonous work are contraindicated, the employee must be dismissed.

The ability to work in a large team is an important personal skill, without which it is difficult to imagine the work of a mechanic.

Contraindications to work in this position are violations of the vestibular apparatus, hearing and visual impairments, a predisposition to colds.

Qualification Requirements

Difficult and responsible this employee Job. The compressor operator must have extensive knowledge in the field of chemistry, physics, electrical engineering. Knowledge of types and types is required to do the job efficiently.

Knowledge of the technological processes used in production is the key to successful work.

It is also necessary to know the principles of operation of the installation, the device of the compressor, electric motors, as well as the instruments with which measurements are taken.

Discharges

According to the reference book, there are 5 categories of compressor operators. For each, its own requirements for professional training are put forward, as well as the responsibilities that the employee must fulfill in this position are described.

In the ETKS classifier, machinists of the second, third, fourth, fifth and sixth categories are distinguished.

The highest is the second category, it is subject to the highest requirements in terms of experience and skills. The sixth, respectively, is the lowest.

The ranks of the compressor unit driver are assigned according to work experience. Responsibilities, as well as the level of remuneration, depend on the category.

Second rank

The operator of the compressor installation of the second category serves compressors with an operating pressure of up to 10 kgf / cm 2 (1 MPa). The flow rate of this unit is 5 m 3 / min.

Responsibilities include:

• starting, stopping and regulating compressors;
• monitoring the operation of auxiliary equipment, as well as the compressors themselves;
• lubrication of parts of mechanisms experiencing friction;
• prevention of malfunctions in the compressor;
• elimination of the arisen malfunctions;
• monitoring the operation of safety devices;
• repair of drive motors;
• filling oil into emergency tanks and service tanks, as well as pumping out oil;
• participation in the repair of compressor equipment.

Knowledge for the second category

The instruction of the compressor installation driver presupposes the availability of professional knowledge, without which the performance of direct duties will be impossible.

The employee must know:

• principles of turbocharger operation;
• the principle of operation of a reciprocating compressor;
• operation of steam engines and turbochargers;
• the principle of operation of electric motors;
• how to troubleshoot motors and compressors;
• methods of using instruments for measurements and control, as well as the purpose of each instrument;
• station piping diagram;
• working pressure and air temperature corresponding to each mode;
• the permissible temperature to which the operating unit of the unit can be heated;
• ways to eliminate overheating, as well as measures to prevent overheating;
• brands of oils used in the unit for lubrication of units.

Third rank

The compressor plant operator is trained not only at vocational schools or universities. There are advanced training courses, after which the student is issued a certificate of awarding him a higher grade.

Turbocompressors and stationary compressors with an operating pressure of up to 10 kgf / cm 2 (1 MPa), flow - above 5 m 3 / min. and up to 100 m 3 / min. Or installations with pressures above 10 kgf / cm 2 (1 MPa) and feed up to 5 m 3 / min. when working with non-hazardous gases driven by different motors.

For a specialist of the third category, duties are:

• regulation and start-up of compressors, engines and turbochargers;
• maintaining the required parameters of the compressor;
• switching between different units;
• prevention of emergency situations in the operation of the station;
• preparation of technical documentation for the operation of the serviced equipment;
• taking part in the repair of units and parts of the station.

Knowledge for the third grade

An employee with a third grade should know:

• reciprocating compressors, internal combustion engines, electric motors, steam engines and installations;
• technical characteristics of the described units and rules for their maintenance;
• arrangement of control and measuring equipment, maintenance rules and technical characteristics;
• installation piping diagram;
• the documentation required for the operation of the installation;
• fundamentals of thermodynamics, as well as electrical engineering;
• gas properties in compressor operation.

Fourth grade

The driver with the specified discharge serves turbocompressors and stationary compressors up to 10 kgf / cm 2 (1 MPa). The flow rate in these installations is more than 100 m 3 / min.

The work consists in:

• establishment and maintenance of an advantageous mode for compressor operation;
• monitoring the health of engines, devices, mechanisms;
• participation in the inspection and repair of equipment (according to the qualifications of a locksmith with the 3rd grade).

Knowledge for the fourth grade

To perform duties at a high level, he must know:

• design features, as well as the device of various types of compressors, internal combustion engines, turbochargers, electric motors, complex instruments for control and measurement, fittings and equipment, steam engines;
• layouts of pipelines, steam pipelines, tanks and fittings;
• diagrams according to which the automatic device for blocking the operation of the station is located;
• technical characteristics of the compressors to be serviced;
• electricity consumption rates for normal work stations;
• consumption rates of materials for the production of gases or compressed air.

Fifth rank

The fifth-grade driver serves automated stations up to 100 m 3 / min.

His responsibilities are:

• switching over, as well as taking out the equipment for repair and into a standby state;
• regulation of technical processes;
• drawing up lists of defects, as well as lists for equipment repair;
• repair of station equipment (qualification of a locksmith of the 4th grade);
• repair of internal combustion engines and compressor units in the field and on-site conditions.

Knowledge for the fifth grade

A fifth-grade mechanic should know the internal structure well enough.

Required knowledge:

• kinematic diagrams of turbochargers, electric motors, steam engines, internal combustion engines;
• high pressure compressor devices;
• operating rules and characteristics of auxiliary equipment, steam engines, electric motors, turbocompressors;
• technological processes of the station;
• Compressor efficiency and applied structures and systems.

Sixth rank

The work of a sixth-grade machinist requires the greatest concentration, and knowledge must be supported not only by theory, but also by practice. Due to the fact that the serviced units have a large capacity, the employee must be able to carry out:

• monitoring the correct operation of the equipment of the entire station;
• regulation of the process for the production of products of the station's work;
• preparation of defective statements;
• equipment repair (qualification of a locksmith of the 5th category).

Knowledge for the sixth grade

Knowledge is required:

• turbocharger design;
• kinematic diagrams;
• various power equipment: steam engines, electrical equipment, internal combustion engines;
• characteristics for the operation of power plants of compressors.

Work safety

Labor protection of the compressor unit operator is regulated by the current legislation of the Russian Federation. Labor legislation, as well as health and safety standards, establish the permissible operating limits for mechanics. The mode of work is consistent with the qualifications and is based on the health status of the employee.

Vacancies

In Moscow, the operator of compressor units receives from 80,000 rubles. An employee of this category is required for large manufacturing enterprises... To submit your resume for consideration, you need to monitor the labor market and track emerging vacancies.