How to make an information stand with your own hands. How to make a stand with your own hands - a step-by-step algorithm of actions (61 photos) What information stands are made of

What are they made of information stands? This question is asked by those who, for one reason or another, need to make an information stand. In this article I will try to explain in detail from what, and most importantly, how information stands are made.

So, let's begin. The main thing in the information stand is its basis. It depends on how long the stand will last. The main material for the stand is PVC (sheet plastic). But not all plastics are the same! For example, "Chinese"-made plastics have a more porous structure and, as a result, are more brittle than plastics (PVC) produced in Germany, Hungary, and Israel. V Lately became very popular plastics (PVC) Russian manufacturers, the quality of which also leaves much to be desired. So what is the difference between "Chinese" plastics (PVC) and non-Chinese ones? Everything is very simple. The difference is in the quality of the plastic itself (PVC)! As known all polymer-containing materials (plastic and plastic materials, including self-adhesive films) - cellular polycarbonate, PVC plastic, plexiglass, polystyrene can change their appearance under the influence of different temperatures. So "Chinese" plastic (PVC) is the most subject to change. It is very brittle at low temperatures (from 0°C), and too soft at high temperatures (+25°C and above) and as a result of change appearance very noticeable. If over time your stand has become "wavy", or a corner has broken off during installation, you should know that Chinese plastic was used in the production of your stand.

The second, no less important component of the information stand are the pockets (files) located on the base. Pockets are made from organic glass(PMMA), transparent polyethylene (PET) or transparent plastic (PVC), and are attached to the base with double-sided tape or special glue (depending on the purpose of the information stand). To date, the most popular material for the manufacture of pockets (files) is transparent PVC with a thickness of 0.6 mm. This is a fairly durable material and at the same time it is relatively inexpensive, for example, than a pocket made of plexiglass (PMMA). When designing an information stand, it is important to consider the size of the pocket, as it is different from the size of the sheet placed inside it! So, for example, a pocket for an A4 sheet (210x297) will have a size of (225x305) mm. Specialists of the company "Obavoka" will be happy to help you in the development of information stands for your tasks!

The third component of the booth is its "cap", the name of the booth. The hat is made of PVC film of various colors using plotter cutting or large format printing.

I would like to say that this is it, the stand is ready! But it's not. The most important thing is ahead - to make an information stand with your own hands!

First you need to make a sketch of the future stand, observing the dimensions and placement of pockets on the stand. It is important to consider the distance between the pockets and the indentation from the edge of the base. It is recommended to make a distance between pockets of 20 mm in horizontal and vertical rows. Indent from the edge of the base to the pocket 30 mm. The booth cap usually has a height of 100 mm.

From the tool: a metal square, a stationery knife, a felt squeegee (you can do without it), a metal ruler.

Let's get started!

Using a square, we make markings on the sheet material, since it is important that the stand is "in the corner", and cut out the base with a clerical knife and a metal ruler. To do this, we apply the ruler to the markup and use a clerical knife to make a cut. It is important not to try to cut the material the first time, otherwise you can ruin the base. With smooth movements, draw a clerical knife along the ruler, each time increasing the pressure on the blade. Then the cut will turn out even and neat. Repeat the action on four sides.

Next, we apply (roll) a hat. To do this, place the cap (sticker) at the top of the base and fix it with a small weight, such as a small weight. At the same time, turn the base itself with the upper part towards you, for convenience. While pressing the sticker against the base with your left hand, gently lift the right side of the sticker from the base by about 10 centimeters. Separate the backing from the sticker by 5 centimeters and fold it inward. Using a felt squeegee, roll the separated part of the hat to the base. Next, gradually removing the substrate, apply a cap to the base.

Remaining pockets. We take a ruler and mark out the location of the pockets on the basis of the stand. Next, we place the pockets on the basis, according to the markup. Pressing the pocket firmly against the base with your left hand, lift the edge of the pocket with your right hand and remove the protective tape from the adhesive tape, after which we fix the edge of the pocket on the base by pressing the edge of the pocket with your right hand. The pocket is fixed. We do the same with the two remaining sides of the pocket and the rest of the pockets on the stand!

That's all! Your stand is ready! It remains to place it indoors.

PS. The company "Obavoka" uses sheet plastics (PVC) for the manufacture of stands of only world brands High Quality! Also in our company you can buy sheet plastic for stands, pockets for stands and caps for them.

Now you understand what stands for schools, information stands for hospitals, information stands for parents in kindergarten, an information stand at the enterprise, a stand in a kindergarten.

If you want to order ready-made stands - please contact our company! We use only high-quality materials, and your stand can be made very quickly! V individual cases within a few hours!

I hope that this information was helpful to you!

I decided to somehow make a couple of rotary stands, as in the photo. Usually these are used for hanging satin ribbons on reels. Height 220 cm, width 50 cm - so, the thing is not small.

The stand must be swivel. I had to break my head a bit. It was necessary to select a pipe, a bearing and a washer so that together they would form a swivel assembly (the design of the swivel assembly itself will be presented later). At the beginning, I thought that I could just pick them up to each other "in place", but very soon I realized the viciousness of this path and went to study literature.

After considering different combinations, I chose the best option:

From "GOST 3262-75. Steel water and gas pipes." chose a pipe - "sorokovka" with an outer diameter of 48.

The frame of the stand is made of profile pipe 25x25x1.5. Legs from a pipe 20x40x2. Crossbeams from a bar 7 mm.

From "GOST 7872-89. Single and double thrust ball bearings." chose bearings of the 8210 series with an inner diameter of 50.

In "GOST 11371-78. Washers." I found washers d48 with accuracy class A and an inner diameter of 50.

But if there were no problems with the pipe and bearings, then the M48 washers of accuracy class A are not too hot commodity. Couldn't find any for sale.
I found Leirus Business Center LLC on the Internet, located in my city, which had these washers in the price list on the site. I called the specified phone number, but their managers are strange. What is the minimum order, how many pieces are in the package, what is the price per package and what is the delivery time, it was not possible to find out. I'm not talking about what accuracy class according to GOST 11371-78 their washers belong to.

I solved the problem with washers simply - I turned to a turner, who turned them for 70 rubles apiece.

Unfortunately, I don't have pipe clamps. But it is important to accurately set the angles and distances between the frame elements. To do this, I cut out a template from plywood with the required dimensions and exact angles and simply fixed the profile pipes on it with clamps.

Yes, and there is no bed for the grinder either. Therefore, the cutting of parts is not always ideal.

But after welding, everything falls into place. Boiled with Monolith 2 mm electrodes. Current 50 A with a margin.

Thanks to a simple template, we managed to get a good result.

We clean the seams with a grinder.

Using the same template, I set up the vertical racks of the frame. It wasn't perfect, but acceptable.

One of the elements of the swivel mechanism is a washer, which is located at the bottom of the frame and which rests on the bearing. It is mounted on four segments, which must be welded accurately enough. To do this, at the beginning we weld the first crossbar at the bottom of the frame.

Now we weld the second crossbar

And having made the same sections, we place the puck in the center

We fix the washer by welding.

In the upper part of the frame there is another crossbar with a piece of pipe welded perpendicular to it. This piece of pipe will also become an element of the swivel frame in the future.
Part of the future stand is ready. Let's call this part "Rotor" because that's what will rotate.

Adjustable feet will be welded on the ends of the legs. Drilled holes for them.

I made another template from the same plywood. It fixes the position of the legs relative to the lower edge of the column and the angle of the legs.

It also fixes the position of the leg relative to the axis of the column.

Using a square, set the position of the legs relative to each other

After work, the template was slightly charred at the welding points, but still quite suitable.

I welded a washer on the stator at the bottom. The thrust bearing will rest on this washer, and the rotor washer on it.

In the upper part of the stand, it was necessary to insert some kind of bushing into the pipe so that the thinner pipe would swell freely in it. Wherein lathe I don't have either. I had to scratch my head a little more.
As a result, for the manufacture of the sleeve, I took a plastic coupling for polyethylene pipes 32 mm. It fits perfectly into the "sorokovka" water and gas pipe. The connection is tight, but it can be disassembled by hand.

Via drilling machine adjusted the inner diameter of the bushing. Just in case, so that the plastic does not melt and spoil the forstner drill, I set the minimum speed on the machine - everything went smoothly.

I sawed off the extra parts with a hacksaw and that's it - the sleeve is ready

The rotary mechanism works perfectly - nothing dangles, does not creak, it works smoothly. This is clearly seen in the video:

Now we need to give it all a presentable look. First of all, peel off the rust.

Before painting, we protect the adjustable legs and their threads from paint.

And finally, we paint. It was real torment. The fact is that parts of the stands occupied the entire space in the workshop. They had to be painted in parts and rearranged all the time, because they could not be approached from all sides. As a result, in some places, the fresh coating was damaged from an accidental touch, either with the elbow, or with the back, or with something else. So also the omnipresent experience added inconvenience.
Therefore, I had to expand the workshop a little and start another room - for painting. More about it here:
Now painting jobs do not cause too many problems and do not take too much time.

Some difficulties arose when painting the crossbars. They are made from 7mm bar. At the beginning, the strategy was as follows: lay them out on a plane, apply paint with an airbrush, let dry. Then turn them over on the other side and apply paint again with an airbrush. For the third time, the bars should be painted over on all sides. So it was in theory.

But in practice, the bars could not be turned to the other side. Because they are crooked and this curvature always tends to take a lower position. After laying the second layer and seeing that I paint almost the same side, I decided to paint the rods by hand. Oh, and what a chore it is! Two coats took almost two full days.

It was no less dreary to install almost five hundred rod holders, screwing almost a thousand self-tapping screws with a drill into them. By the way, it was not easy to buy them. I had to wander in search of the right amount of identical rod holders.

After installing the rod holders on the frame, we make the final assembly of the stands. At the bottom, the swivel mechanism consists of two washers separated by a bearing. This node holds the entire vertical load.

In the upper part, the rotary mechanism consists of two pipes inserted one into the other and separated by a plastic sleeve. This node holds lateral loads.

It remains to cut the crossbars

And install them in the rod holders

Turntables are almost ready.

There is one more detail left. In the upper part of the stand there is a box, which is put on top and logos are applied to the walls. I decided to make it from 18mm plywood, although Gamma, which served as the prototype, makes it from tin.

In the upper part of the box on the inside there is a ledge with which it is held on the frame of the stand.

I painted the boxes in my new paint brushes, the link to which is above in this article.
The first layer on a tree always lays down disgustingly - bald spots, a pile that has risen and other joys of a painter.
Therefore, I usually put two layers (and sometimes more) with intermediate polishing of the coating with an abrasive sponge. The first primer layer can be diluted with a stronger solvent so that it is absorbed deeper into the wood.

The second layer goes much better.

The stands turned out great. In some places even better than the prototype. In general, the joy of a job well done is present))

Anna Svetlichnaya

Dear colleagues!

In connection with the introduction of the Federal State Educational Standard, the task educator organize work with parents, one of the forms of which is information corners. I want to bring to your attention stand making master class"Nobody is forgotten, nothing is forgotten!"

First, we need to develop a layout. I did it in PowerPoint

To work we need...

Width of our stand 1 meter, i.e. 2 tiles.

Since the layout is 4 wavy stripes, then 1 template is suitable for both the concave and the convex part, only upside down.

Apply the template to tiles, circle with a pencil.

top cut tiles

and apply to the bottom of the part, combine, so that the cut coincides, and when we assemble booth I didn't have to tweak the details.

We turn the part over, circle it and cut it out from another tiles, then the details will match.

Details are best immediately numbered on the reverse side. Thus, 4 strips are cut, each of which consists of 2 parts.

For painting, mix color with PVA glue, achieving the desired shade. We color the parts according to the numbering, not forgetting to paint over the edges.

Name booth typing on a computer, making templates, tracing and cutting out tiles.

We also need flowers. We make a template.

We will have flowers voluminous. To do this, we will have to cut the template several times.

First, cut off the cup from the flower. We circle on tile received parts.

Then we cut the cup into 2 parts, circle the smaller one, cut it out.

We cut off the upper part from the flower template, circle the resulting part on tiles.

We cut off another part of the template and circle the very bottom of the flower on tiles.

It turns out bulk flower.

Now let's paint all the details with the desired color. When the paint is dry glue it together "The Dragon". Details of flowers are glued together on the reverse side with scraps tiles.

More for making booth we need the Eternal Flame. In our case, the picture is cut out, glued with a pencil glue and laminated with adhesive tape. Cut out with a clerical knife, retreating from the edge of the picture a couple of mm.

Now we will deal with the pockets that are needed to place information. They can be made from: files, corners, folders, or you can buy ready-made ones. We will make pockets from folders. The folder needs to be cut.

With the help of self-adhesive paper, we make a frame. Glue double sided tape on the reverse side.

Now let's collect our stand. Parts are fastened together on the reverse side with scraps tiles and glue"The Dragon".Then we place our details on it: pockets, flowers, letters and Eternal Flame. Fill in the pockets with information.

Children are indefatigable dreamers, and their activities can endlessly touch and delight adults. When the results of creativity are in a clearly visible specially designated place, young fidgets are delighted.

Exhibition board equipment is not always associated with large cash outlays. Any interested parent is able to make children's stands with their own hands.

How to choose the right material

Among a large assortment modern stands, more and more consumers opt for cork boards. They are easy to use, reliable, durable, affordable.

Natural material - cork oak bark - satisfies general requirements safety for children's products and has a number of positive qualities:

• ecologicaly clean;
• easy to clean, does not attract dust;
• moisture resistant;
• refractory;
• chemical resistant;
• not damaged by fungus, insects;
• not electrified;
• shockproof;
• wear-resistant.

Cork stands will be a win-win option for both home and kindergarten.

How to make a stand

You do not need to have special craft skills and knowledge to please yourself and your children with a functional novelty in the house.

Think in advance how to harmoniously fit the new stand into the interior.

You can experiment both with the color of the board itself - paint it or upholster it with a fabric of the desired color, and with the frame, choosing the best combination.

The frame is usually made of wood, plastic, metal profile. It is also advised to use cable channels, the width of which is slightly greater than the thickness of the board.

Choose the type of wall mount for the stand: non-removable version with glue or free hanging on hinges.

The minimum set of blanks and tools used, 30 minutes of work - and the result will be on the wall.

Determine the desired dimensions of the stand, prepare a cork sheet to fit.

Choose the material for the back wall - plywood, fiberboard.

Glue both sheets. Glue - liquid nails, you can use another. Degrease the surface first, after applying the glue, press the parts tightly against each other. If desired, cover the working surface of the stand with a cloth.

Attach the previously prepared frame to the base. If desired, attach loops for fastening on the reverse side.

Fix the stand to the wall with glue or double-sided tape for a non-removable option. For an alternative method - hang on loops.

How to rationally use the stand

After you have made a stand with your own hands, you can begin to actively exploit it.

Note!

There are two main formatting methods. You can fix pockets on the surface of the board. These can be files for papers, or transparent pieces of thin plexiglass, fixed on double-sided tape.

This type of design is used for information stands.

Sheets of paper are placed in the pockets with important information that parents should know about the working hours, routine, rules of behavior for children in kindergarten.

The information can be updated daily (food menu) or as needed.

Stands are actively used by people of different ages both at work and at home. Reminders of important events, planning for the near future, pleasant memories captured in photographs, visualization of your desires, a convenient organizer - in the list useful features Everyone will independently add the most relevant for themselves.

On cork demonstration stands, the necessary items - photographs, pictures, paper notes, small souvenirs are fastened with buttons, pins, tailor's needles.

Note!

The surface of the board does not suffer from this, there are no holes visible to the eye. When designing a stand for children, you need to make sure that sharp objects cannot harm the kids.

The stand, on which educators attach the results of children's work for the day, is always popular with caring parents. And the children are happy to present new crafts and arrange mini-exhibitions already in the apartment.

Take a photo of the filled stand as a souvenir, and let it be constantly updated - the world of children's imagination is inexhaustible.

DIY booth photo

Note!

The first step in creating a booth is choosing the material for its base.

Cork board - in the first place among all materials. Differs in affordability, its practicality. The basis of this material will last more than one year.

Stands for children's institutions are made from the cork oak bark. The material is safe for health and has a number of other advantages:

• moisture resistance;
• opposes mechanical influences;
• withstand impact force;
• resistance to chemicals;
• resistance to fire;
• full resistance to the appearance of fungi and mold;
• ease of maintaining cleanliness on the surface;
• long service life.

The reverse side of the stand can be plywood and fiberboard.

The algorithm for performing work on the manufacture of the stand

Stands are made of 3 types:

1. The simplest design with a minimum number of elements.
2. Complex design with a large number of elements.
3. The combined design consists of pictures, objects and text.

• It is important to choose a place that will be well lit and for everyone to see. Visually imagine that the stand will fit perfectly into the interior of the room.
• Flowers are welcome. But the edging on the stand should fit into its overall design in color.
• The frame of the stand can be made of plastic strips, wooden slats. A metal profile is used.
• A strong fastening mechanism is very important.
• In the process, you will need tools, including a knife with a sharp blade. They need to be prepared.
• Based on the location of the future stand, you can determine its size.
• Cork wood is cut to the selected dimensions.
• The cork board with the back side material is glued together with “liquid nails”. Before that, they are degreased.
• The resulting base of the stand can be covered with material.
• A frame is attached to the front.
• Loops for a removable version of the stand are attached to the back side.
• If the stand will not be removed from the wall, then it can be placed on the wall using double-sided tape.
• The stand is ready for registration.

A very easy way to create a stand for information sheets, posters, announcements with the help of a ceiling skirting board. The material is affordable. One plinth strip is the top of the stand, the second strip will be the bottom border. Between them there is a gap to the height of an A4 sheet. Sheets with information are attached to the strips with buttons or pins.

If you need to place a large amount of information in a small space, then a stand-book will be an ideal option. It is called a demo system or a system for demonstrating information. Such stands are common at railway stations, bank premises, exhibition halls, shopping centers.

They differ in location: wall, floor, table and universal stands. But such stands can also be organized for the exhibition of creative drawings at school and in kindergarten.

Base design

The design of the base must begin with "pockets". Pieces of plexiglass and files are used as the main material for them. They are attached with double sided tape. The number of "pockets" directly depends on the size of the base of the stand itself.

For information boards, the design of the "pocket" is more necessary. For example, a board with information about the menu: the information sheet changes in the “pocket” every day. You can create an information board about the schedule of performances of children's groups, duty in the school class of students, passing exams at an educational institution.

• Choose a stand theme: School of Music and her studying proccess; corner healthy lifestyle life; congratulations on the holiday and many other options. The heading of the stand should be brightly designed. It can be compared with calling card. Therefore, a bright design and a catchy name will not hurt. Letters can be cut from plastic or printed matter.
• The stand can be with information about future events and with reporting information, a “pocket” for wishes and suggestions can be created.
• Information sheets are attached to the base of the stand using buttons, pins. But with these tools you need to be careful in children's institutions.

Tip: bright pictures will help convey information. Especially if this needs to be conveyed to children. But they must correspond to the subject of the text. Heroes from cartoons will help bring information closer.

• Information stands are placed in places with high traffic. Stands with information of an entertaining nature should be in recreation areas where children relax and communicate more.
• The stand on which the creative achievements of children are placed can also be placed at home. The child will be able to share his victories with his parents. To create such a corner, you do not need to have great skills at all. But for the family, this is a big push for unity.
• There is another type of stand - a demonstration stand. Their function: to act as exhibition shelves for photographs, souvenirs, pictures. Shelves can be either wooden without a base wall or with plexiglass attached to the base.

In a family where a baby has just been born, you can create a stand-memory. And fix every minute of changes in the life of the baby on it. Closer to the first anniversary of the baby, a whole folder of interesting material will be collected, which will remind you of the minutes of his growth.

It can take about 30 minutes to make the simplest stand. With a complex design, you will need to tinker. But the result will please you, and others will treat you with a sense of gratitude.