Samsung scx 3400 does not print. Printing a Samsung SCX Series Report Page
A fairly common problem among users of the Samsung SCX-3400 printer is the situation when the printer does not print. Previously printing normally or installed for the first time, it doesn’t matter - from this article you will learn the causes of the malfunction and simple tips to fix it.
Why won't Samsung SCX-3400 print?
Paper is jammed in the printer
Typically, if a paper jam occurs in a printer, it will stop printing. At the same time, the lights and indicators begin to flash. At the same time, a corresponding error message can be observed on the monitor screen, as well as suggestions for troubleshooting. Follow the instructions on the screen to fix the problem.
Before doing this. If paper is jammed in the printer, a simple reset will help. Not a computer. Unplug the printer, wait a few seconds, and then plug it back in. Not always, but sometimes this is enough to make the printer work. The printer and all its elements will restart. Jammed paper will come out by itself.
If the method did not help, for example, too much paper was jammed, use the assistant's advice on the monitor screen. But such an adviser does not always appear that will help solve the problem with jammed paper. For example, your computer does not have the dedicated printer diagnostic software installed. Therefore, if there are no notifications, remove the jammed sheets yourself. Open the printer cover, as well as all other elements that allow free paper exit. You do not need to completely disassemble the device.
Gently remove the sheet or sheets from the printer. When removing the paper, be careful not to pull it with force, so as not to tear it off. In the worst case, if, nevertheless, the sheet is accidentally cut off, a piece of paper remains in the printer, gently hook the edge with tweezers or a similar tool, pull it towards you. In any case, the printer will not print until the paper is completely removed. And even if it does, it becomes unsafe, in terms of the fact that important printer elements can fail.
Paper jam in the printer
A similar situation, a message like "Paper jam in the printer" is displayed on the monitor screen. Printing pauses until the paper is pulled out. Remove paper from printer.
The difference between this problem and the previous one is that, if in the first case the paper can still be somehow removed without disassembling the printer, then in the second case, it jams, breaks, and folds to such an extent that even manually it is not always possible to remove it from there. .
How to take paper out of the printer?
To remove paper from the Samsung SCX-3400 printer, open the printer cover as well as all closing elements that allow paper to exit. Carefully remove it with gentle movements. No need to pull out sharply - you can tear off most of the sheet. In this case, extracting the remains will be much more difficult.
But it often happens that they still tear off. They took one end - they pull. A little paper went, pull harder. As a result, the sheet is torn off and paper remains in the printer. If this does happen, use tweezers or another similar tool to grab the edge of the sheet and slowly pull until it is completely out.
Samsung printer jamming paper?
Let's consider for what reasons, in fact, a jam occurs. Why does the Samsung SCX-3400 jam the paper?
Paper is magnetized in the printer
Often this problem is observed with sheets that have been run through a laser printer and have received some electrostatic charge.
For example, you need to print a document on both sides of a sheet - make duplex printing. Over time, the electrified sheets become magnetic to each other. To prevent this from happening, take a stack of printed sheets, flip through them all, tap the edge against a hard surface, wait a while, and start typing again.
If you often have to deal with double-sided printing, in this case, the usual antistatic agent that is used for clothes will help.
Paper stuck together in the printer
If a certain number of sheets have been printed, the print element heats up, causing the sheets of paper to heat up. If you continue printing on the back sides of the same sheets, they stick together. Scrolling and tapping will help correct the situation. Moreover, when flipping through the sheets, in order to make sure, put the stack on the table and pull on one sheet. If another one stretches behind it, then the sheets stick together and it is too early to continue printing. Scroll through the entire stack again. Blow, or something, on them, shake ...
If too much paper is loaded in the tray, the printer may accidentally pick up several sheets, thereby preventing them from passing through the print element and jamming as if stuck together. Restarting the printer will help.
Bad paper in the printer
Is it worth talking about it at all? After all, the user knows what he is doing when he inserts old, wrinkled sheets into the printer in the hope of getting a normal document. And why? Of course, if the importance of such a document is indifferent, then you can print whatever you want.
On the other hand, if you need to test the printer by turning on test printing, it is more expedient to insert already used draft sheets. Why not? Still, the best advice would be to limit such printing techniques, so as not to subsequently break the printer due to some unsuccessful attempt to pull the paper out of the printer.
Paper not suitable for printer
Another option is also quite common. There are different paper formats, different quality, size, weight. If the printer has jammed paper, you may be using the wrong paper!? Too thin or vice versa. Check, if necessary, replace.
Paper is not inserted straight into the printer
They accidentally put the sheets unevenly in the tray and the printer grabbed it just as unsuccessfully. It happens that the printer itself unevenly grabs the paper. Maybe he's just tired!? Cool down the printer, let it rest. The printer may not pick up paper at all. Make sure the sheets are stacked correctly.
Printer cover open
If the cover is open or not tightly closed in any printer, including the Samsung SCX-3400, the printer will not print. Sometimes even a pinhole in the cover can cause the printer to stop printing. The reason may be the failure of the closing element, locking devices. And therefore, while any of the covers is open, the printer does not print.
In order to correct the situation, check all doors, covers and other closing elements.
Samsung printer driver crashed
Current drivers and other software can be found on the manufacturer's website. Use only official resources and always check what you download from the web.
Use programs that will prepare your computer to interact with the printing device. Update your drivers.
|
This page describes how to print a configuration page for Samsung SCX series printers and MFPs from the control panel. These reports contain information about firmware, serial number, network settings, consumables remaining, and more.
Samsung SCX-3200/3205
- Configuration report:
Samsung SCX— 3205W
In standby mode, press the "STOP" key for about 2 seconds. In this case, a Printer Configuration Report will be printed.
If you need a network settings report, hold down the "STOP" key for about 4 seconds.
If you hold down the familiar key for 6 seconds or more, a supplies status report will be printed. Where can you find out the balance on the chip.
If the printer is blocked due to the end of the cartridge life, then the reports cannot be printed until you insert a new cartridge, or until you change the chip to a working one.
Samsung SCX-3400/3405/3407
There are two ways to print a report.
- Configuration report:
Press the "STOP" key in the standby mode, and hold it for no more than 3 seconds, release it after the indicator flashes.
— Report on the status of consumables:
If you need to know the balance of the chip and other parameters of consumables, press and hold the "STOP" key for more than 4 seconds.
Relatively quickly press the buttons on the control panel in the following order: “+” “+” “STOP” “-” “-” “STOP” “STOP”. The code “UC” should appear on the display, now press the “+” button until the code “AA” appears on the screen. Now we press "START", the printer will print several pages with a configuration report and the status of consumables.
Samsung SCX-3400F/3405 F/3405 FW
Press the menu button 3 times, then you will see the inscription “System Setup” on the screen, press “OK”.
Use the "Left" "Right" buttons to find the "Report" section and press "OK". Next, select the report you need and confirm with the "OK" button.
Second way:
Press the keys in the sequence MENU - # - 1934 - MENU, then select TECH MENU, in which you will find the REPORT section. Here select ALL REPORT and confirm with the "OK" button. All reports will be printed.
Samsung SCX-4200/4220
In Idle mode, press the "Menu" key until "Report" appears. By clicking on "OK" you will see the line "System data", after which you confirm the print with the same button.
Samsung SCX-4300
To print a report on this MFP, press the Menu button 8 times. The display will show the inscription "Report ...", it remains only to confirm the printing with the "OK" key.
Samsung SCX-4600/4623x/482xFN/4833x
Make sure the printer is on and in standby mode. Press the "Menu" button 3 times, after which you will see the line "System Setup" on the screen, press "OK".
Using the keys, get to the "Reports" section, and enter it with "OK". Here, select the report you need, and confirm with the same “OK” button.
Samsung SCX-4650/4650N/4655FN
Samsung SCX-4727x/4728x/4729x
In standby mode, press "Menu", in which select "System Settings". Next, find the "Reports" section. Here, select "Configuration" or "Consumable Details", and confirm printing.
You can print the report in the second way.
Press the key combination Menu - # - 193 - #. Next, find the "Report" section, then select "All Report". In this case, both reports will be printed.
Printing a Samsung SCX Series Report Page updated: August 9, 2017 by: admin
Seal _ 72
Color Adjustment
When there are color differences between the image on the screen
computer and the resulting print, adjust such
settings like color contrast or color level.
The printer driver allows you to make print settings for
various needs.
1.
Open the window Print setup(See section "Access to
2. Open a tab Graphic arts. For information about
print options in the menu Print setup talk to
online guide.
Color mode: available as color print ( Color), So
and printing in grayscale ( shades of gray). Meaning Color
usually results in the best print quality
color images. To print a color image in
grayscale select value shades of gray.
Black optimization improves the quality
black printing. Using this function
may slow down the print speed.
Press the button to manually adjust the color
Additionally on the menu Color mode. For adjustment
print colors move the slider on the tab Levels or
select tab equalization to calculate the correction
colors by the print driver.
Additionally: to set additional
options, click Additionally. (Only
PCL driver)
Font and text: select option Darken text,
to make the text darker. For black and white printing
use the parameter Print all text in black.
Raster compression: determines the degree of compression
images to transfer them from the computer to the printer.
If you set it to Maximum,
The print speed will increase, but the print quality will decrease. (Only
PCL driver)
Graphics controller: this function is intended
for clearer display of font edges and thin
lines, which improves the readability of the text, as well as for
color channel synchronization when printing in color
Grayscale Enhancement: enhancement function
shades of gray ensures the reproduction of details on
photographs and improve contrast and
legibility of color documents printed in
grayscale mode. (PCL driver only)
Sharp Edges: This feature is for more
clear display of font edges and thin lines, which
improves the readability of the text.
Save Toner: This feature allows you to extend the
cartridge service and reduce the cost of printing a single
pages. However, print quality is not significant.
decreases.
To reduce toner consumption, move the slider from
values Without saving to value Max. quantity
save.
3. Press the button OK or Seal until the window Seal not
will close.
Adjusting print clarity and smoothness
Screen Options
This feature affects the resolution and legibility of color prints.
Three modes are provided: Standard., Improved and
Detailed.
1.
To change print settings from an application,
Open the window Print setup(See section "Access to
2. On the tab Graphic arts select item Additionally In chapter
Color mode.
3.
Open a tab equalization.
4.
Set the desired options in the menu Screen.
Default settings: mode settings apply
Screen.
Ordinary: when this mode is selected, print on a page
will be smoothed out.
Improved: when this mode is selected, the text on
the printed page will be crisp and the images and
photos - smoothed.
Detailed: when this mode is selected, all details on
page will be printed clearly.
5. Click the button OK.
Changing the default print settings
Most Windows system applications can override
printer driver settings. First, set the settings to
application, and then other settings in the print driver.
1.
On a Windows system, open the menu Start.
2.
On a Windows 2000 system, select
Setting > Printers.
For Windows XP/Server 2003, select Printers and
faxes.
On a Windows Server 2008/Vista system, sequentially
select items Control Panel > Equipment and sound
> Printers.
In Windows 7, select the items in sequence Panel
management > Devices and printers.
On a Windows Server 2008 R2 system, select
points Control Panel > Equipment and sound >
Devices and printers.
3.
Right click on the device.
4.
For Windows XP/Server 2003/Server 2008/Vista, select the command
Print setup.
In Windows 7 and Windows Server 2008 R2, select in the context
menu item Print setup.
If available near item Print setup icon
arrows ( ) you can select another driver for this
printer.
5.
Set the options you want on each tab.
6.
Click the button OK.
You can change the settings for all print jobs in the
Print setup.
Popular
- How to use laundry soap in everyday life Household soap in medicine
- The influence of the energy of old and other people's things on our lives
- Printing a Samsung SCX Series Report Page
- Faint printing on the right edge of HP P1005 and similar
- Resetters - inkjet portal, online store, forum, superprint ciss, dctec ink, everything for your printer
- How to contact the Magnit Cosmetic hotline?
- Does it make sense to divide costs into variable and fixed costs?
- Aliexpress Standard Shipping package tracking
- How to delete photos or an album in classmates
- Letter to Santa Claus: sample text, design and address